Russia, US & Chinese EVA's from 2000 till end 2010

Int



This list contains all spacewalks performed since the beginning of 2000 where an astronaut has fully, or partially left the spacecraft.
As of August 7, 2010, 193 astronauts have made spacewalks (out of 515 people who have gone into Earth orbit). Only 11 women have been on spacewalks, in part because the EVA suits are too large for some women.

2000 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
182. Mir - PE-28
EVA 1
Russia: Sergei Zalyotin
Russia: Alexander Kaleri
May 12, 2000
10:44
May 12, 2000
15:36
- 4 h, 52 min
Kaleri and Zalyotin tested a leak sealant and inspected a malfunctioning solar panel on Kvant-1. A final photographic record of the outer surfaces of Mir was made during a panorama-inspection.
183. STS-101
EVA 1
James Voss
USA Jeffrey Williams
May 22, 2000
01:48
May 22, 2000
08:32
- 6 h, 44 min
Inspected and secured U.S.-built cargo crane known as the Orbital Replacement Unit Transfer Device, completed assembly of a Russiasian cargo crane called Strela, and replaced one of Unity's two early communication antennas.
184. STS-106
EVA 1
USA: Edward Lu
Russia: Yuri Malenchenko
September 11, 2000
04:47
September 11, 2000
11:01
- 6 h, 14 min
Attached cabling that integrated the Zvezda module fully to the rest of the ISS, and constructed and attached a magnetometer that serves as a backup navigation system for the station.
185. STS-92
EVA 1
USA: Leroy Chiao
USA: William McArthur
October 15, 2000
14:27
October 15, 2000
20:55
- 6 h, 28 min
Connected two sets of cables to provide power to heaters and conduits located on the Z1 tRussias, relocated two communication antenna assemblies, and installed a toolbox for use during future on-orbit construction.
186. STS-92
EVA 2
USA: Michael Lopez-Alegria
USA: Peter Wisoff
October 16, 2000
14:15
October 16, 2000
21:22
- 7 h, 07 min
Installed the Pressurized Mating Adapter (PMA)-3 docking port, and prepared the Z1 tRussias for the installation of the solar arrays.
187. STS-92
EVA 3
USA: Leroy Chiao
USA: William McArthur
October 17, 2000
14:30
October 17, 2000
21:18
- 6 h, 48 min
Installed two DC-to-DC converter units atop the station's Z1 Truss. Reconfigured cabling to new docking port PMA-3, and installed a tool storage box on the Z1 Truss.
188. STS-92
EVA 4
USA: Michael Lopez-Alegria
USA: Peter Wisoff
October 18, 2000
15:00
October 18, 2000
21:56
- 6 h, 56 min
Removed a grapple fixture on the Z1 Truss, deployed a Z1 utility tray, Manual Berthing Mechanism latches for Z1 were cycled and opened, and demonstrated the Simplified Aid for EVA Rescue (SAFER) pack's abilities.
189. STS-97
EVA 1
USA:Joseph Tanner
USA: Carlos I. Noriega
December 3, 2000
18:35
December 4, 2000
02:08
- 7 h, 33 min
Attached the P6 Truss to the Z1 Truss, and prepared the solar arrays for deployment. Prepared the radiator for the power system deployment.
190. STS-97
EVA 2
USA: Joseph Tanner
USA: Carlos Noriega
December 5, 2000
17:21
December 5, 2000
23:58
- 6 h, 37 min
Configured the space station to use power from the P6. Positioned the S-band antenna for use by the space station. Prepared the station for the arrival of the U. S. Laboratory, Destiny.
191. STS-97
EVA 3
USA: Joseph Tanner
USA: Carlos Noriega
December 7, 2000
16:13
December 7, 2000
21:23
- 5 h, 10 min
Positioned a floating potential probe to measure the plasma field surrounding the space station, performed repair work to increase tension in the starboard solar array blankets that did not stretch out completely during deployment, and installed a centerline camera cable outside the Unity node.

2001 spacewalks



#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
192. STS-98
EVA 1
USA: Thomas D. Jones
USA: Robert Curbeam
February 10, 2001
15:50
February 10, 2001
23:24
- 7 h, 34 min
Removed protective launch covers and disconnected power and cooling cables between Destiny and Atlantis, while crewmembers inside moved the 3800 cubic feet (107.6 m³) laboratory from the payload bay to its home on the Unity node. Curbeam and Jones then connected electrical, data and cooling lines to the lab, during which a small amount of ammonia crystals leaked from one of the hoses, prompting a decontamination procedure.
193. STS-98
EVA 2
USA: Thomas Jones
USA: Robert Curbeam
February 12, 2001
15:59
February 12, 2001
22:49
- 6 h, 50 min
Installed the shuttle docking adapter onto Destiny, installed insulating covers over the pins that held Destiny in place during launch, attached a vent to the lab's air system, installed handrails and sockets on the exterior of Destiny, and attached a base for the future space station robotic arm.
194. STS-98
EVA 3
USA: Thomas Jones
USA: Robert Curbeam
February 14, 2001
14:48
February 14, 2001
20:13
- 5 h, 25 min
Attached a spare communications antenna to the station exterior, double-checked connections between the Destiny lab and its docking port, released the restraints on a Station cooling radiator, inspected solar array connections at the top of the station, and tested a technique for a spacewalker to carry an incapcitated crew member to the shuttle airlock. This was the 100th U.S. spacewalk.
195. STS-102
EVA 1
USA: James Voss
USA: Susan Helms
March 11, 2001
05:12
March 11, 2001
14:08
- 8 h, 56 min
Prepared Pressurized Mating Adapter-3 for repositioning from Unity’s Earth-facing berth to the port-side berth to make room for Leonardo, the Italian Space Agency-built Multi-Purpose Logistics Module. Removed a Lab Cradle Assembly from the shuttle's cargo bay and installed it on the side of Destiny, and installed a cable tray to Destiny for later use by the station’s robot arm. After re-entering the shuttle's airlock, Voss and Helms remained ready to assist if any troubles installing the docking port were encountered by the crew inside the shuttle. Longest space walk in shuttle history.
196. STS-102
EVA 2
USA: Andy Thomas
USA: Paul W. Richards
March 13, 2001
05:23
March 13, 2001
11:44
- 6 h, 21 min
Installed an External Stowage Platform for spare station parts, attached a spare ammonia coolant pump to the platform, finished connecting several cables put in place on the first EVA for the station's robotic arm. Inspected a Unity node heater connection, and inspected of an exterior experiment, the Floating Potential Probe.
197. STS-100
EVA 1
Canada: Chris Hadfield
USA: Scott Parazynski
April 22, 2001
11:45
April 22, 2001
18:55
- 7 h, 10 min
Installed the station's UHF antenna, and the Canadian Space Agency made Canadarm2. Connected cables to give the arm power and allow it to accept computer commands from inside the lab. Hadfield became the first Canadian spacewalker.
198. STS-100
EVA 2
Canada: Chris Hadfield
USA: Scott Parazynski
April 24, 2001
12:34
April 24, 2001
20:14
- 7 h, 40 min
Connected the Power Data Grapple Fixture circuits for Canadarm2 onto Destiny, removed an early communications antenna, transferred a spare Direct Current Switching Unit from the shuttle's payload bay to an equipment storage rack on the outside of Destiny.
199. ISS Exp. 2
EVA 1
Russia: Yury Usachev
USA: James S. Voss
June 8, 2001
14:21
June 8, 2001
14:40
- 0 h, 19 min
Installed the docking cone onto the Zarya module, in preparation for the arrival of the Russiasian Pirs docking compartment. Only EVA to be conducted from the transfer compartment at the forward end of the Zvezda Service Module.
200. STS-104
EVA 1
USA: James F. Reilly July 15, 2001
03:10
July 15, 2001
09:09
- 5 h, 59 min
Installed the Quest Joint Airlock onto the Unity node and connect power cables to it.
201. STS-104
EVA 2
USA: James F. Reilly July 18, 2001
03:04
July 18, 2001
09:33
- 6 h, 29 min
Installed one of two high-pressure nitrogen tanks, and one of two high-pressure oxygen tanks onto Quest, and installed grapple fixture and trunnion covers.
202. STS-104
EVA 3
USA: James F. Reilly July 21, 2001
04:35
July 21, 2001
08:37
- 4 h, 02 min
First EVA conducted from the Quest airlock. Installed the second high-pressure nitrogen tank, and the second oxygen tank onto the Quest airlock. After completion of the tank installation, Gernhardt and Reilly conducted a photography session around the new airlock.
203. STS-105
EVA 1
USA: Daniel Barry
USA: Patrick Forrester
August 16, 2001
13:58
August 16, 2001
20:14
- 6 h, 16 min
Installed an Early Ammonia Servicer onto the station's P6 tRussias, co-location of the foot restraint in a stowed location, and installed the Materials International Space Station Experiment (MISSE)-1 and 2 containers onto the Quest airlock.
204. STS-105
EVA 2
USA: Daniel Barry
USA: Patrick Forrester
August 18, 2001
13:42
August 18, 2001
19:11
- 5 h, 29 min
Installed heater cables and handrails onto the station's Destiny laboratory.
205. ISS Exp. 3
EVA 1
Russia: Vladimir Dezhurov
Russia: Mikhail Tyurin
October 8, 2001
14:24
October 8, 2001
19:22
- 4 h, 58 min
Installed cables between the Pirs (ISS module), and the Zvezda module to allow spacewalk radio communications between the two sections. Installed handrails onto Pirs, and installed an exterior ladder to assist spacewalkers leaving Pirs. Installed a Strela cargo crane.
206. ISS Exp. 3
EVA 2
Russia: Vladimir Dezhurov
Russia:
October 15, 2001
09:17
October 15, 2001
15:08
- 5 h, 51 min
Installed Russiasian commercial experiments (MPAC-SEEDS) onto the exterior of the Pirs docking compartment.
207. ISS Exp. 3
EVA 3
Russia: Vladimir Dezhurov
USA: Frank Culbertson
November 12, 2001
21:41
November 13, 2001
02:46
- 5 h, 05 min
Connected cables on the exterior of Pirs for the Kurs automated docking system, completed checks of the Strela cargo crane, and inspected and photographed a panel of a solar array on Zvezda that had a portion of a panel not fully unfolded.
208. ISS Exp. 3
EVA 4
Russia: Vladimir Dezhurov
Russia: Mikhail Tyurin
December 3, 2001
13:20
December 3, 2001
16:06
- 2 h, 46 min
Removed an obstruction that prevented a Progress resupply ship from firmly docking with the station, and took pictures of the debris and of the docking interface.
209. STS-108
EVA 1
USA: Linda Godwin
USA: Daniel Tani
December 10, 2001
17:52
December 10, 2001
22:04
- 4 h, 12 min
Installed insulating blankets around two Beta Gimbal Assemblies that rotate the station's solar array wings, and performed get-ahead tasks in preparation for STS-110's spacewalks.

2002 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
210. ISS Exp. 4
EVA 1
Russia: Yuri Onufriyenko
USA: Carl Walz
January 14, 2002
20:59
January 15, 2002
03:02
- 6 h, 03 min
Moved the cargo boom for the Russiasian Strela crane from PMA1 (Pressurized Mating Adapter) to the exterior of the Pirs docking compartment, installed an amateur radio antenna onto the end of Zvezda.
211. ISS Exp. 4
EVA 2
Russia: Yuri Onufriyenko
USA: Daniel Bursch
January 25, 2002
15:19
January 25, 2002
2118
- 5 h, 59 min
Installed six deflector shields for Zvezda's jet Truss, installed a second amateur radio antenna, attached four science experiments, and retrieved and replaced a device to measure material from the thrusters.
212. ISS Exp. 4
EVA 3
USA: Carl Walz
USA: Daniel Bursch
February 20, 2002
11:38
February 20, 2002
17:25
- 5 h, 47 min
Tested the Quest airlock, and prepared it for the four spacewalks that will be performed during STS-110. The first spacewalk to be based out of Quest without a space shuttle at the station.
213. STS-109
EVA 1
USA: John Grunsfeld
USA: Richard Linnehan
March 4, 2002
06:37
March 4, 2002
13:38
- 7 h, 01 min
Grunsfeld and Linnehan removed the old starboard solar array on Hubble Space Telescope and replaced it with a new, smaller and more powerful third generation solar array. The old array was stowed in Space Shuttle Columbia for return to earth.
214. STS-109
EVA 2
USA: Jim Newman
USA: Michael Massimino
March 5, 2002
06:40
March 5, 2002
13:56
- 7 h, 16 min
Newman and Massimino removed the old port solar array on the Hubble Space Telescope and replaced it with a new third generation solar array. The old array was stowed in Space Shuttle Columbia for return to earth. The two astronauts then removed and replaced the Reaction Wheel Assembly (RWA).
215. STS-109
EVA 3
USA: John Grunsfeld
USA: Richard Linnehan
March 6, 2002
08:28
March 6, 2002
15:16
- 6 h, 48 min
The spacewalk was delayed 2 hours by a leak in Grunsfeld's spacesuit. The old Power Control Unit (PCU) was removed from Hubble and stowed for return to earth. A new, more powerful PCU, sized to match the more productive solar arrays, was installed.
216. STS-109
EVA 4
USA: Jim Newman
USA: Michael Massimino
March 7, 2002
09:00
March 7, 2002
16:30
- 7 h, 30 min
Newman and Massimino removed the Faint Object Camera from the aft shroud of the Hubble Space Telescope and installed the Advanced Camera for Surveys ;(ACS) in the same location. After stowing the Faint Object Camera in the Space Shuttle Columbia for return to earth, the Electronic Support Module was installed in the aft shroud.
217. STS-109
EVA 5
USA: John Grunsfeld
USA: Richard Linnehan
March 8, 2002
08:46
March 8, 2002
16:06
- 7 h, 20 min
Linnehan and Grunsfeld installed an experimental Cryocooler for NICMOS inside the aft shroud of the Hubble Space Telescope and connected it to the Electronic Support Module installed the day before. Then the two spacewalkers installed the Cooling System Radiator to the outside of the Hubble, and connected it to the NICMOS.
218. STS-110
EVA 1
USA: Steven Smith
USA: Rex Walheim
April 11, 2002
14:36
April 11, 2002
22:24
- 7 h, 48 min
Began installing the S0 Truss onto Destiny, initial power and data connections installed between the station and S0, and installed two forward struts that permanently hold the truss in place.
219. STS-110
EVA 2
USA: Jerry Ross
USA: Lee Morin
April 13, 2002
14:09
April 13, 2002
21:39
- 7 h, 30 min
Continued S0 Truss installation, power and data cable connections installed between S0 and the station, and installed two aft struts that permanently hold the truss in place.
220. STS-110
EVA 3
USA: Steven Smith
USA: Rex Walheim
April 14, 2002
13:48
April 14, 2002
20:15
- 6 h, 27 min
Released the claw that was used in the initial attachment of the S0 Truss, installed connectors that will be used to route power to Canadarm2 when it is on the truss, released launch restraints from the Mobile Transporter, and removed a small thermal cover the Mobile Transporter's radiator.
221. STS-110
EVA 4
USA: Jerry Ross
USA: Lee Morin
April 16, 2002
14:29
April 16, 2002
21:06
- 6 h, 37 min
Pivoted the "Airlock Spur", which will be used by spacewalkers in the future as a path from the airlock to the truss, installed handrails onto S0, partially assembled a platform, and installed two floodlights.
222. STS-111
EVA 1
USA: Franklin Chang-Diaz
France: Philippe Perrin
June 9, 2002
15:27
June 9, 2002
22:41
- 7 h, 14 min
Attached a Power Data Grapple Fixture to the P6 truss, removed debris panels from Endeavours payload bay and attached them to a temporary location on PMA1 (Pressurized Mating Adapter), and removed thermal blankets to prepare the Mobile Base System (MBS) for installation onto the station's Mobile Transporter.
223. STS-111
EVA 2
USA: Franklin Chang-Diaz
France: Philippe Perrin
June 11, 2002
15:27
June 11, 2002
22:41
- 5 h, 00 min
Attached Mobile Base System to the Mobile Transporter, attached power, data and video cables from the station to the MBS.
224. STS-111
EVA 3
USA: Franklin Chang-Diaz
France: Philippe Perrin
June 13, 2002
15:16
June 13, 2002
22:33
- 7 h, 17 min
Replaced Canadarm2's wrist roll joint, and stowed the old joint in the shuttle's payload bay to be returned to Earth.
225. ISS Exp. 5
EVA 1
Russia: Valery Korzun
USA: Peggy Whitson
August 16, 2002
09:25
August 16, 2002
1348
- 4 h, 23 min
Installed six micro meteoroid debris panels onto Zvezda. These panels were the first 6 of 23 panels that will be installed to add more micro-meteoroid protection to Zvezda.
226. ISS Exp. 5
EVA 2
Russia: Valery Korzun
Russia: Sergei Treshchev
August 26, 2002
05:27
August 26, 2002
10:48
- 5 h, 21 min
Installed a frame on the outside of Zarya for spacewalk assembly tasks, installed new samples on a pair of Japanese Space Agency experiments housed on Zvezda, installed devices on Zvezda that would simplify the routing of tethers during future spacewalks, and installed two additional ham radio antennas on Zvezda.
227. STS-112
EVA 1
USA: David Wolf
USA: Piers Sellers
October 10, 2002
15:21
October 10, 2002
22:22
- 7 h, 01 min
Released launch locks that held the S1 truss radiators in place during launch, attached power, data and fluid lines between the S1 truss and S0, deployed the station's second S-Band communications system, installed the first of two external camera systems, and released launch restraints on the tRussias' mobile spacewalk workstation, Crew and Equipment Translation Aid (CETA).
228. STS-112
EVA 2
USA: David Wolf
USA: Piers Sellers
October 12, 2002
14:31
October 12, 2002
20:35
- 6 h, 04 min
Installed a second camera system, released more radiator launch locks, removed insulation covers on quick-disconnect fittings near the Z1 and P6 junction and to install Spool Positioning Devices, released starboard-side launch restraints on the CETA cart, and attached Ammonia Tank Assembly cables.
229. STS-112
EVA 3
USA: David Wolf
USA: Piers Sellers
October 14, 2002
14:08
October 14, 2002
20:44
- 6 h, 36 min
Removed and replaced the Interface Umbilical Assembly on the station's Mobile Transporter, installed two jumpers that will allow ammonia coolant to flow between the S1 and S0 Trusses, released a drag link and stowed it, and installed Spool Positioning Devices (SPD) on ammonia lines.
230. STS-113
EVA 1
USA: Michael Lopez-Alegria
USA: John Herrington
November 26, 2002
19:49
November 27, 2002
02:34
- 6 h, 45 min
Initial installation of the P1 tRussias, installed connections between the P1 and the S0 tRussias, released launch restraints on the CETA cart, installed Spool Positioning Devices (SPDs) onto the station, removed a drag link on P1 that served as a launch restraint, and installed a Wireless video system External Transceiver Assembly onto the Unity node.
231. STS-113
EVA 2
USA: Michael Lopez-Alegria
USA: John Herrington
November 28, 2002
18:36
November 29, 2002
00:46
- 6 h, 10 min
Installed fluid jumpers where the S0 and the P1 are attached to each other, removed the P1's starboard keel pin, installed another Wireless video system External Transceiver Assembly onto the P1, and relocated the CETA cart from the P1 to the S1 tRussias.
232. STS-113
EVA 3
USA: Michael Lopez-Alegria
USA: John Herrington
November 30, 2002
19:25
December 1, 2002
02:25
- 7 h, 00 min
Herrington successfully troubleshot a mobility issue with the CETA cart. Lopez-Alegria and Herrington then completed the planned EVA activities by installing more Spool Positioning Devices, reconfiguring electrical harnesses that route power through the Main Bus Switching Units, and attaching Ammonia Tank Assembly lines.

2003 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
233. ISS Exp. 6
EVA 1
USA: Kenneth Bowersox
USA: Donald Pettit
January 15, 2003
12:50
January 15, 2003
19:41
- 6 h, 51 min
Released the remaining launch locks on the P1 radiator assembly, removed debris on a sealing ring of Unity's docking port, and tested an ammonia reservoir on the station's P6 truss.
234. ISS Exp. 6
EVA 2
USA: Kenneth Bowersox
USA: Donald Pettit
April 8, 2003
12:40
April 8, 2003
19:06
- 6 h, 26 min
Reconfigured cables on the S0 (S-Zero), S1 and P1 trusses, replaced a Power Control Module on the Mobile Transporter, installed Spool Positioning Devices on Destiny, and reinstalled a thermal cover on an S1 Radiator Beam Valve Module.

2004 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
235. ISS Exp. 8
EVA 1
USA: Michael Foale
Russia: Alexander Kaleri
February 26, 2004
21:17
February 27, 2004
01:12
- 3 h, 55 min
Replaced cassette containers that held sample materials for a microgravity experiment, attached the Russiasian experiment Matryoshka to Zvezda, and removed a JAXA micro-meteor impact experiment. Spacewalk was cut short due a cooling system malfunction in Kaleri's spacesuit.
236. ISS Exp. 9
EVA 1
Russia: Gennady Padalka
USA: Michael Fincke
June 24, 2004
21:57
June 24, 2004
22:10
- 0 h, 13 min
Spacewalk cut short due to a pressure problem in Fincke's prime oxygen tank in his spacesuit. Mission managers decided to reschedule the spacewalk for June 30.
237. ISS Exp. 9
EVA 2
Russia: Gennady Padalka
USA: Michael Fincke
June 30, 2004
21:19
July 1, 2004
02:59
- 5 h, 40 min
Replaced a Remote Power Controller (RPC) that failed in late April, causing a loss of power in Control Moment Gyroscope No. 2 (CMG 2). This spacewalk was the first time that primary Mission Control was transitioned from Moscow to Houston during an EVA.
238. ISS Exp. 9
EVA 3
Russia: Gennady Padalka
USA: Michael Fincke
August 3, 2004
06:58
August 3, 2004
11:28
- 4 h, 30 min
Removed laser retro reflectors from the Zvezda assembly compartment, and installed three updated laser retro reflectors and one internal videometer target in preparation for the Automated Transfer Vehicle ;(ATV). Installed two antennas, and removed and replaced Kromka experiment packages.
239. ISS Exp. 9
EVA 4
Russia: Gennady Padalka
USA: Michael Fincke
September 3, 2004
16:43
September 3, 2004
22:04
- 5 h, 20 min
Padalka and Finke continued preparations for arrival of the European Space Agency's Automatic Transfer Vehicle (ATV). They replaced the Zarya Control Module flow control panel, installed four safety tether fairleads on Zarya's handrails, installed three communications antennas, and removed covers from the antennas.

2005 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
240. ISS Exp. 10
EVA 1
USA: Leroy Chiao
Russia: Salizhan Sharipov
January 26, 2005,
07:43
January 26, 2005,
13:11
- 5 h, 28 min
Chiao and Sharipov completed the installation of the Universal Work Platform, mounted the European commercial experiment Rokviss (Robotic Components Verification on ISS) and its antenna, installed the Russian Biorisk experiment, and relocated a Japanese exposure experiment.
241. ISS Exp. 10
EVA 2
USA: Leroy Chiao
Russia: Salizhan Sharipov
March 28, 2005,
06:25
March 28, 2005,
11:31
- 5 h, 06 min
Chiao and Sharipov installed navigational and communications equipment for the arrival of the first Automated Transfer Vehicle (ATV), and deployed an 11-pound Russian Nanosatellite.
242. STS-114
EVA 1
Japan: Soichi Noguchi
USA: Stephen Robinson
July 30, 2005,
05:46
July 30, 2005,
12:36
- 6 h, 50 min
Noguchi and Robinson demonstrated shuttle thermal protection repair techniques and enhancements to the Station’s attitude control system. They also installed a base and cabling for an External Stowage Platform, rerouted power to Control Moment Gyroscope-2 (CMG-2), retrieved two exposure experiments, and replaced a faulty global positioning system antenna on the station.
243. STS-114
EVA 2
Japan: Soichi Noguchi
USA: Stephen Robinson
August 1, 2005,
04:44
August 1, 2005,
11:58
- 7 h, 14 min
Noguchi and Robinson removed a faulty CMG-1 from the Z1 truss, installed the faulty CMG-1 into Space Shuttle Discovery's payload bay, and installed a new CMG-1 on the Z1 truss segment.
244. STS-114
EVA 3
Japan: Soichi Noguchi
USA: Stephen Robinson
August 3, 2005,
04:14
August 3, 2005,
10:15
- 6 h, 01 min
Noguchi and Robinson photographed and inspected Discovery’s heat shield, removed two protruding gap fillers from between tiles in the forward area of the orbiter’s underside, and installed the amateur radio satellite PCSAT2.
245. ISS Exp. 11
EVA 1
Russia: Sergei Krikalev
USA: John L. Phillips
August 18, 2005,
19:02
August 19, 2005,
00:00
- 4 h, 58 min
Krikalev and Phillips retrieved one of three canisters from the Biorisk experiment, removed the Micro-Particles Capturer experiment and Space Environment Exposure Device from Zvezda, retrieved the Matroska experiment, and installed an Automated Transfer Vehicle (ATV) docking television camera.
246. ISS Exp. 12
EVA 1
USA: William McArthur
Russia: Valery Tokarev
November 7, 2005,
15:32
November 7, 2005,
20:54
- 5 h, 22 min
McArthur and Tokarev installed and set up the P1 Truss camera, retrieved a failed Rotary Joint Motor Controller (RJMC), jettisoned a Floating Potential Probe, and removed and replaced a remote power controller module on the Mobile Transporter. This was the first Quest airlock-based spacewalk since April 2003.

2006 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
247. ISS Exp. 12
EVA 2
USA: William McArthur
Russia: Valery Tokarev
February 3, 2006,
9:55
February 3, 2006,
16:27
- 5 h, 43 min
McArthur and Tokarev released SuitSat-1, retrieved the Biorisk experiment, photographed a sensor for a micrometeoroid experiment, relocated an adapter for a small crane, and tied off the surviving Umbilical cable of the Mobile Transporter.
248. ISS Exp. 13
EVA 1
Russia: Pavel Vinogradov
USA: Jeffrey Williams
June 1, 2006
23:48
June 2, 2006
06:19
- 6 h, 31 min
Vinogradov and Williams repaired a vent for the station's oxygen-producing Elektron unit, retrieved a Biorisk experiment, retrieved a contamination-monitoring device from Zvezda, and replaced a malfunctioning camera on the Mobile Base System.
249. STS-121
EVA 1
USA: Piers Sellers
USA: Michael E. Fossum
July 8, 2006
13:17
July 8, 2006
20:48
- 7 h, 31 min
Sellers and Foale installed a blade blocker in the zenith Interface Umbilical Assembly (IUA) to protect the undamaged power, data and video cable, and rerouted the cable to prepare for the second EVA. They also tested the combination of the Space Shuttle Remote Manipulator System (SSRMS) and the Orbiter Boom Sensor System (OBSS) as a platform for astronauts to make repairs to a damaged orbiter.
250. STS-121
EVA 2
USA: Piers Sellers
USA: Michael E. Fossum
July 10, 2006
7:14
July 10, 2006
14:01
- 6 h, 47 min
Sellers and Fossum restored the International Space Station’s Mobile Transporter rail car to full operation, and delivered a spare pump module for the station’s cooling system. Sellers' SAFER pack came loose during the EVA, requiring Fossum to stop twice during the spacewalk to secure the pack with safety tethers.
251. STS-121
EVA 3
USA: Piers Sellers
USA: Michael E. Fossum
July 12, 2006
6:20
July 12, 2006
13:31
- 7 h, 11 min
Sellers and Fossum used an infrared camera to shoot 20 seconds of video of selected Reinforced carbon-carbon (RCC) panels on the shuttle wing’s leading edge, and then moved to the payload bay to test a shuttle tile repair material known as NOAX on pre-damaged shuttle tiles that were flown in a test container.
252. ISS Exp. 13
EVA 2
USA:Jeffrey Williams
Germany: Thomas Reiter
August 3, 2006
14:04
August 3, 2006
19:58
- 5 h, 54 min
Williams and Reiter installed the Floating Potential Measurement Unit (FPMU), two materials on Materials International Space Station Experiment (MISSE) containers, a controller for a thermal radiator rotary joint on the S1 truss, a starboard jumper and spool positioning device (SPD) on S1, a light on the truss railway handcart, and installed and replaced a malfunctioning GPS antenna. They then tested an infrared camera designed to detect damage in a shuttle's reinforced carbon-carbon (RCC) thermal protection tiles. Inspection and photography of a scratch on the Quest airlock hatch completed the EVA.
253. STS-115
EVA 1
USA: Joe Tanner
USA: Heidemarie Stefanyshyn-Piper
September 12, 2006
10:17
September 12, 2006
15:43
- 5 h, 26 min
Tanner and Stefanyshyn-Piper completed initial installation of the P3/P4 truss onto the space station. They connected the power cables on the truss, and released the launch restraints on the solar array blanket box, the Beta Gimbal Assembly, and the solar array wings. They also configured the Solar Alpha Rotary Joint (SARJ), and removed two circuit interrupt devices to prepare for STS-116. Stefanyshyn-Piper became the seventh American woman to walk in space.
254. STS-115
EVA 2
Canada: Steven MacLean September 13, 2006
9:05
September 13, 2006
16:16
- 7 h, 11 min
Burbank and MacLean continued installation of the P3/4 truss onto the station, and activated the SARJ.
255. STS-115
EVA 3
USA: Joe Tanner
USA: Heidemarie Stefanyshyn-Piper
September 15, 2006
10:00
September 15, 2006
16:42
- 6 h, 42 min
Tanner and Stefanyshyn-Piper installed a radiator onto the P3/4 truss, powered up a cooling radiator for the new solar arrays, replaced an S-Band radio antenna, and installed insulation for another antenna. Tanner took photos of the shuttle’s wings using an infrared camera to test the camera's ability to detect damage.
256. Exp. 14
EVA 1
Russia: Mikhail Tyurin
USA: Michael Lopez-Alegria
November 22, 2006
23:17
November 23, 2006
04:55
- 5 h, 39 min
An unusual "Orbiting golf shot" event was sponsored by a Canadian golf company through the Russiasian Federal Space Agency. López-Alegría put the tee on the ladder outside Pirs, while Tyurin set up a camera and performed the golf shot. López-Alegría and Tyurin inspected and photographed a Kurs antenna on Progress 23, relocated an Automated Transfer Vehicle (ATV) WAL antenna, installed a BTN neutron experiment, and jettisoned two thermal covers from the BTN.
257. STS-116
EVA 1
USA: Robert Curbeam
Sweden: Christer Fuglesang
December 12, 2006
20:31
December 13, 2006
03:07
- 6 h, 36 min
Curbeam and Fuglesang installed the ISS P5 Truss, replaced a broken video camera on the S1 truss, and prepared the new truss for relocation of the P6 truss to its permanent location.
258. STS-116
EVA 2
USA: Robert Curbeam
Sweden: Christer Fuglesang
December 14, 2006
19:41
December 15, 2006
00:41
- 5 h, 00 min
Curbeam and Fuglesang reconfigured the station's electrical wiring, placing electrical channels 2–3 on the P3/P4 truss into service, thus enabling full advantage of the new solar arrays. They then relocated two handcarts that run along rails on the station’s main truss, put a thermal cover on the station’s robotic arm, and installed tool bags for future spacewalkers.
259. STS-116
EVA 3
USA: Robert Curbeam
USA: Sunita Williams
December 16, 2006
19:25
December 17, 2006
02:57
- 7 h, 31 min
Curbeam and Williams completed rewiring the station's electrical system, activating electrical circuits 1 and 4, preparing for installation of more solar power arrays. They then installed a robotic arm grapple fixture, and positioned three bundles of Russian debris shield panels outside Zvezda. Additional time was spent trying to help retract the P6 solar array panel by shaking the panel's blanket box from its base. Williams became the 8th American woman to perform an EVA, and the 9th woman to walk in space overall.
260. STS-116
EVA 4
USA: Robert Curbeam
Sweden: Christer Fuglesang
December 18, 2006
19:00
December 19, 2006
01:38
- 6 h, 38 min
Curbeam and Fuglesang assisted ground controllers with retracting the P6 solar array panels in preparation for moving them during the upcoming flight STS-120. Curbeam, on his seventh spacewalk, set a single-flight EVA record with four spacewalks in a single shuttle mission.

2007 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
261. Exp. 14
EVA 2
USA: Michael Lopez-Alegria
USA: Sunita Williams
January 31, 2007
15:14
January 31, 2007
23:09
- 7 h, 55 min
López-Alegría and Williams reconfigured one of the two cooling loops serving Destiny from the temporary to permanent system, connected a cable for the Station-to-Shuttle Power Transfer System (SSPTS), installed six cable cinches and two winch bars to secure the starboard radiator of the P6 Truss, and then installed a shroud over it. They then removed one of two fluid lines from the Early Ammonia Servicer (EAS) on the P6 TRussias in preparation for jettisoning the EAS on a later EVA.
262. Exp. 14
EVA 3
USA: Michael Lopez-Alegria
USA: Sunita Williams
February 4, 2007
13:38
February 4, 2007
20:49
- 7 h, 11 min
López-Alegría and Williams reconfigured the second of the two cooling loops serving Destiny from the temporary to permanent system, completed work with the Early Ammonia Servicer (EAS) on the P6 TRussias, photographed the inboard end of the P6 starboard solar wing in preparation for its retraction during STS-117, removed a sunshade from a multiplexer-demultiplexer data relay device, and continued work on the SSPTS.
263. Exp. 14
EVA 4
USA: Michael Lopez-Alegria
USA: Sunita Williams
February 8, 2007
13:26
February 8, 2007
20:06
- 6 h, 40 min
López-Alegría and Williams removed two thermal shrouds on two Rotary Joint Motor Controllers (RJMC) on the P3 truss, removed two large shrouds from P3 Bays 18 and 20, and jettisoned the shrouds away from the station. They also deployed an Unpressurized Cargo Carrier Assembly Attachment System (UCCAS) on the upper face of the P3 truss, removed two launch locks from the P5 truss, and connected four cables of the SSPTS to the Pressurized Mating Adapter (PMA-2) at the forward end of Destiny where shuttles dock.
264. Exp. 14
EVA 5
USA: Michael Lopez-Alegria
Russia: Mikhail Tyurin
February 22, 2007
10:28
February 22, 2007
16:45
- 6 h, 18 min
López-Alegría and Tyurin retracted the antenna of the Progress cargo carrier at the aft port of the Zvezda service module, photographed a Russian satellite navigation antenna, and replaced a Russiasian materials experiment. They also inspected and photographed an antenna for the Automated Transfer Vehicle (ATV), photographed a German robotics experiment, and inspected, remated, and photographed hardware connectors. Tyurin experienced some cooling problems and fogging on his visor during the spacewalk.
265. Exp. 15
EVA 1
Russia: Oleg Kotov
Russia: Fyodor Yurchikhin
May 30, 2007
19:05
May 31, 2007
00:30
- 5 h, 25 min
Kotov and Yurchikhin installed Service Module Debris Protection (SMDP) panels on Zvezda and rerouted a Global Positioning System antenna cable.
266. Exp. 15
EVA 2
Russia: Oleg Kotov
Russia: Fyodor Yurchikhin
June 6, 2007
14:23
June 6, 2007
20:00
- 5 h, 37 min
Kotov and Yurchikhin installed a section of Ethernet cable on the Zarya module, installed additional Service Module Debris Protection (SMDP) panels on Zvezda, and deployed a Russiasian scientific experiment.
267. STS-117
EVA 1
USA: James F. Reilly
USA: John D. Olivas
June 11, 2007
20:02
June 12, 2007
02:17
- 6 h, 15 min
Reilly and Olivas completed the installation of ISS S3/S4 Truss by attaching bolts, cables, and connectors. They then released the launch restraints on four Solar Array Blanket Boxes in preparation for deployment of the arrays.
268. STS-117
EVA 2
USA: Patrick G. Forrester
USA: Steven Swanson
June 13, 2007
18:28
June 14, 2007
01:44
- 7 h, 16 min
Forrester and Swanson assisted in retraction of the solar panels on the P6 Truss. When Forrester tried to install a drive-lock assembly, a partial failure was discovered. The failure was due to the S3/S4 SARJ motor control circuits being wired in reverse. Some launch restraints were left in place to prevent the possibility of undesired rotation.
269. STS-117
EVA 3
USA: James F. Reilly
USA: John D. Olivas
June 15, 2007
17:24
June 16, 2007
01:22
- 7 h, 58 min
Reilly and Olivas repaired the Orbital Maneuvering System (OMS) pod thermal blanket, finished the P6 solar array retraction, and installed a hydrogen ventilation valve onto Destiny.
270. STS-117
EVA 4
USA: Patrick G. Forrester
USA: Steven Swanson
June 17, 2007
16:25
June 17, 2007
22:54
- 6 h, 29 min
Forrester and Swanson retrieved a television camera and its support structure from an External Stowage Platform attached to the Quest airlock, and installed it on the S3 truss, verified the Drive Lock Assembly (DLA) 2 configuration, and removed the last six SARJ launch restraints. Then they installed a computer network cable on the Unity node, opened the hydrogen vent valve on the Destiny laboratory, and tethered two orbital debris shield panels on the station’s service module.
271. Exp. 15
EVA 3
USA: Clayton Anderson
Russia: Fyodor Yurchikhin
July 23, 2007
10:25
July 23, 2007
18:06
- 7 h, 41 min
Anderson and Yurchikhin replaced components for the Mobile Transporter's redundant power system, jettisoned an ammonia tank and flight support equipment, and cleaned the Common Berthing Mechanism (CBM) on the nadir port of Unity.
272. STS-118
EVA 1
USA: Richard Mastracchio
Canada: Dafydd Williams
August 11, 2007
16:28
August 11, 2007
22:45
- 6 h, 17 min
Mastracchio and Williams attached the Starboard 5 (S5) segment of the station’s truss, and retracted the forward heat-rejecting radiator from the station’s Port 6 (P6) truss in preparation for moving the P6 truss to its final location at the end of the port truss.
273. STS-118
EVA 2
USA: Richard Mastracchio
Canada: Dafydd Williams
August 13, 2007
15:32
August 13, 2007
22:00
- 6 h, 28 min
Mastracchio and Williams removed the new Control Moment Gyroscope (CMG) from the shuttle's payload bay and installed it onto the Z1 truss. They then stowed the failed CMG onto an External Stowage Platform (ESP-2) for return to earth in a subsequent shuttle flight.
274. STS-118
EVA 3
USA: Richard Mastracchio
USA: Clayton Anderson
August 15, 2007
14:37
August 15, 2007
20:05
- 5 h, 28 min
Mastracchio and Anderson moved two Crew Equipment Translation Aid (CETA) carts from the tracks on the left side of the Canadarm2 Mobile Transporter to its right side. They also relocated an antenna base from the P6 truss to P1, and installed a new transponder and signal processor for an S-band communications upgrade. During the EVA, Mastracchio noted a hole in the second layer of material on the thumb of his left glove. The suit has five protective layers, and the small hole did not cause any danger to Mastracchio, but he returned to the airlock early as a precautionary measure.
275. STS-118
EVA 4
Canada: Dafydd Williams
USA: Clayton Anderson
August 18, 2007
14:17
August 18, 2007
19:02
- 5 h, 2 min
Williams and Anderson retrieved Materials International Space Station Experiment (MISSE) containers 3 and 4, installed the Orbiter Boom Sensor System (OBSS) Boom Stand, installed an External Wireless Instrumentation System (EWIS) antenna, and secured Z1 gimbal locks.
276. STS-120
EVA 1
USA: Scott Parazynski
USA: Douglas Wheelock
October 26, 2007
10:02
October 26, 2007
16:16
- 6 h, 14 min
Parazynski and Wheelock installed the new Harmony module in its temporary location, retrieved the S-Band Antenna Support Assembly, and prepared for the relocation of the P6 truss by disconnecting fluid lines on the P6/Z1 truss segments.
277. STS-120
EVA 2
USA: Scott Parazynski
USA: Daniel M. Tani
October 28, 2007
09:32
October 28, 2007
16:05
- 6h, 33min
Parazynski and Tani disconnected the Z1-to-P6 umbilicals, detached P6 from Z1, configured the S1 radiator, installed handrails onto Harmony, and inspected the S4 starboard Solar Alpha Rotary Joint (SARJ).
278. STS-120
EVA 3
USA: Scott Parazynski
USA: Douglas Wheelock
October 30, 2007
08:45
October 30, 2007
15:53
- 7 hours, 08 minutes
Parazynski and Wheelock attached P6 to P5, installed P6/P5 umbilical connections, reconfigured S1 following its redeployment, and inspected the port SARJ. The inspection showed the SARJ to be in good condition.
279. STS-120
EVA 4
USA: Scott Parazynski
USA: Douglas Wheelock
November 3, 2007
10:03
November 3, 2007
17:22
- 7 hours, 19 minutes
Parazynski and Wheelock inspected and repaired the P6 solar array.
280. ISS Exp. 16
EVA 1
USA: Peggy Whitson
Russia: Yuri Malenchenko
November 9, 2007
09:54
November 9, 2007
16:49
- 6 hours, 55 minutes
Whitson and Malenchenko disconnected and stored the Station-to-Shuttle Power Transfer System cables, stored the PMA-2 (Pressurized Mating Adapter) umbilical, and stowed a Harmony node avionics umbilical into a temporary position.
281. ISS Exp. 16
EVA 2
USA: Peggy Whitson
USA: Daniel Tani
November 20, 2007
10:10
November 20, 2007
17:26
- 7 hours, 16 minutes
Whitson and Tani completed half the external configuration of PMA-2 and Harmony. Fluid, electrical, and data lines were attached, avionics lines were hooked up, heater cables were attached, and a fluid tray was relocated.
282. ISS Exp. 16
EVA 3
USA: Peggy Whitson
USA: Daniel Tani
November 24, 2007
09:50
November 24, 2007
16:54
- 7 hours, 04 minutes
Whitson and Tani completed fluid, electrical, and data line hookups for PMA-2 and Harmony. They connected the Loop B Fluid Tray to the port side of the Destiny laboratory. They then inspected and photographed the starboard Solar Alpha Rotary Joint (SARJ) to assist with troubleshooting on the ground.
283. ISS Exp. 16
EVA 4
USA: Peggy Whitson
USA: Daniel Tani
December 18, 2007
09:50
December 18, 2007
16:46
- 6 hours, 56 minutes
Whitson and Tani inspected the S4 starboard Solar Alpha Rotary Joint (SARJ), and a Beta Gimbal Assembly (BGA). This EVA was the 100th in support of building the International Space Station.
Records: 100th EVA in support of assembly and maintenance of the International Space Station.

2008 spacewalks


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
284. ISS Exp. 16
EVA 5
USA: Peggy Whitson
USA: Daniel Tani
January 30, 2008
09:56
January 30, 2008
17:06
- 7 hours, 10 minutes
Whitson and Tani replaced the Bearing Motor Roll Ring Module on one of the station's solar wings, and inspected and photographed the starboard Solar Alpha Rotary Joint (SARJ).
285. STS-122
EVA 1
USA: Rex J. Walheim
USA: Stanley G. Love
February 11, 2008
14:13
February 11, 2008
22:11
- 7 hours, 58 minutes
Walheim and Love installed a grapple fixture on Columbus while it was still in the shuttle’s payload bay, prepared electrical and data connections on Columbus, and replaced the P1 truss nitrogen (N2) tank used for pressurizing the station's ammonia cooling system.
286. STS-122
EVA 2
USA: Rex J. Walheim
Germany: Hans Schlegel
February 13, 2008
14:27
February 13, 2008
21:12
- 6 hours, 45 minutes
Walheim and Schlegel installed the P1 Truss Nitrogen (N2) tank assembly, stowed the old N2 tank assembly into the shuttle's payload bay, and completed routing for the Station-to-Shuttle Power Transfer System (SSPTS).
287. STS-122EVA 3 USA: Rex J. Walheim
USA: Stanley Love
February 15, 2008
13:07
February 15, 2008
20:32
- 7 hours, 25 minutes
Walheim and Love installed the Solar Monitoring Observatory (SOLAR) telescope and the European Technology Exposure Facility (EuTEF) facility onto an External Stowage Platform (ESP) on Columbus. They retrieved a failed Control Moment Gyroscope (CMG), installed the failed CMG into the shuttle's payload bay, and installed keel pin cloth covers on Columbus.
288. STS-123
EVA 1
USA: Richard M. Linnehan
USA: Garrett Reisman
March 14, 2008
01:18
March 14, 2008
08:19
- 7 hours, 1 minute
Linnehan and Reisman installed the Japanese Experiment Logistics Module, Pressurized Section (ELM-PS) onto its temporary location on top of Harmony, and began assembly of the Special Purpose Dexterous Manipulator (Dextre) .
289. STS-123
EVA 2
USA: Richard M. Linnehan
USA: Michael J. Foreman
March 15, 2008
23:49
March 16, 2008
06:57
- 7 hours, 8 minutes
Linnehan and Foreman continued assembly of Dextre, and attached two "arms" to Dextre.
290. STS-123
EVA 3
USA: Richard Linnehan
USA: Robert L. Behnken
March 17, 2008
22:51
March 18, 2008
05:44
- 6 hours, 53 minutes
Linnehan and Behnken completed the assembly of Dextre. The spacewalkers also installed spare equipment for the station onto an external stowage platform (ESP) on the Quest airlock, including a yaw joint for the station’s robotic arm, Canadarm2, and two spare direct current switching units. Their attempt to attach the MISSE 6 (Materials International Space Station Experiment) experiment onto the Columbus module was unsuccessful as the latching pins failed to engage.
291. STS-123
EVA 4
USA: Robert Behnken
USA: Michael Foreman
March 20, 2008
22:04
March 21, 2008
04:28
- 6 hours, 24 minutes
Behnken and Foreman replaced a Remote Power Control (RPC) module, and tested shuttle thermal tile repair materials and techniques. They then removed a cover from the left arm of Dextre, and removed launch locks from the Harmony module. The spacewalkers also released the launch locks on Harmony’s port and nadir Common Berthing Mechanisms (CBM).
292. STS-123
EVA 5
USA: Robert Behnken
USA: Michael Foreman
March 22, 2008
20:34
March 23, 2008
02:36
- 6 hours, 02 minutes
Behnken and Foreman completed storage of Shuttle Orbiter Boom Sensor System on the Station, installed the ELM‐PS trunnion covers, removed five covers from the starboard SARJ and performed inspections, captured digital photography, and successfully installed of the MISSE 6 experiment on the exterior of the Columbus module.
293. STS-124
EVA 1
USA: Ronald J. Garan, Jr.
USA: Michael E. Fossum
June 3, 2008
16:22
June 3, 2008
23:10
- 6 hours, 48 minutes
Garan and Fossum released the straps on the shuttle's robotic arm elbow joint camera, transferred the OBSS (Orbiter Boom Sensor System) back to the shuttle, and repaired the Japanese Experiment Module, Pressurized Module (JEM-PM), named Kibo, for installation. They also replaced a trundle bearing assembly on the starboard Solar Alpha Rotary Joint, and inspected damage on the SARJ.
294. STS-124
EVA 2
USA: Ronald J. Garan, Jr.
USA: Michael E. Fossum
June 5, 2008
15:04
June 4, 2008
22:15
- 7 hours, 11 minutes
Garan and Fossum installed covers and external television equipment on the JEM (Japanese Experiment Module), prepared the RMS, prepared for the relocation of the ELM-PS (Japanese Experiment Module), prepared a depleted nitrogen tank assembly for removal, and prepared a new one stowed on an external stowage platform for installation. They also removed a television camera with a failed power supply.
295. STS-124
EVA 3
USA: Ronald J. Garan, Jr.
USA: Michael E. Fossum
June 8, 2008
13:55
June 8, 2008
20:28
- 6 hours 33 minutes
Garan and Fossum remove and replaced the starboard nitrogen tank assembly, finished fitting out the Kibō laboratory, and reinstalled the removed television camera with a repaired power supply.
296. ISS Exp. 17
EVA 1
Russia: Sergei Volkov
Russia: Oleg Kononenko
July 10, 2008
18:48
July 11, 2008
01:06
- 6 hours 18 minutes
Volkov and Kononenko removed a pyrotechnic bolt from the docked Soyuz.
297. ISS Exp. 17
EVA 2
Russia: Sergei Volkov
Russia: Oleg Kononenko
July 15, 2008
17:08
July 15, 2008
23:02
- 5 hours 54 minutes
Volkov and Kononenko installed a docking target on the Zvezda service module, installed the Vsplesk experiment, straightened the ham radio antenna, and retrieved the Biorisk experiment.
298. Shenzhou 7
EVA 1
China: Zhai Zhigang
China: Liu Boming (Stand up only)
September 27, 2008
08:38
September 27, 2008
09:00
- 0 hours 22 minuntes
This was the first EVA conducted by China. Zhai collected an experimental package from the outside of the spacecraft and waved a Chinese flag towards a TV camera. Liu supported Zhai's activities while standing in the hatchway.
299. STS-126
EVA 1
USA: Heidemarie Stefanyshyn-Piper
USA: Stephen G. Bowen
November 18, 2008
18:09
November 19, 2008
01:01
- 6 hours, 52 minutes
Stefanyshyn-Piper and Bowen transferred an empty nitrogen tank assembly from ESP3 to the shuttle’s cargo bay, transferred a new flex hose rotary coupler to ESP3 for future use, removed an insulation cover on the Kibo External Facility berthing mechanism, began cleaning and lubrication of the starboard SARJ, and replaced its 11 trundle bearing assemblies.
300. STS-126
EVA 2
USA: Heidemarie Stefanyshyn-Piper
USA: Robert S. Kimbrough
November 20, 2008
17:58
November 21, 2008
00:43
- 6 hours, 45 minutes
Stefanyshyn-Piper and Kimbrough relocated the two Crew and Equipment Translation Aid (CETA) carts from the starboard side of the Mobile Transporter to the port side, lubricated the station robotic arm’s latching end effector A snare bearings, and continued cleaning and lubrication of the starboard SARJ.
301. STS-126
EVA 3
USA: Heidemarie Stefanyshyn-Piper
USA: Stephen G. Bowen
November 22, 2008
18:01
November 23, 2008
01:58
- 6 hours, 57 minutes
Stefanyshyn-Piper and Bowen completed cleaning and lubrication of all but one of the trundle bearing assemblies (TBA) on the starboard SARJ. The final TBA will be replaced during EVA 4.
302. STS-126
EVA 4
USA: Stephen G. Bowen
USA: Robert S. Kimbrough
November 24, 2008
18:24
November 25, 2008
00:31
- 6 hours, 7 minutes
Bowen and Kimbrough completed the replacement of the trundle bearing assemblies on starboard SARJ, lubricated the port SARJ, installed a video camera, re‐installed insulation covers on the Kibo External Facility berthing mechanism, performed Kibo robotic arm grounding tab maintenance, installed spacewalk handrails on Kibo, installed Global Positioning Satellite (GPS) antennae on Kibo, photographed radiators, and photographed trailing umbilical system cables.
303. ISS Exp. 18
EVA 1
Russia: Yuri Lonchakov
USA: Michael Fincke
December 23, 2008
00:51
December 23, 2008
06:29
- 5 hours, 38 minutes
Lonchakov and Fincke installed the electromagnetic energy measuring device, (Langmuir probe) on Pirs, removed the Russiasian Biorisk long-duration experiment, installed the Expose-R experiment package on Zvezda, and installed the Impulse experiment.

2009 spacewalks:


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
304. ISS Exp. 18
EVA 2
Russia: Yuri Lonchakov
USA: Michael Fincke
March 10, 2009
16:22
March 10, 2009
21:11
- 4 hours, 49 minutes
Lonchakov and Fincke installed the EXPOSE-R onto the universal science platform of the Zvezda module, removed tape straps from the area of the docking target on the Pirs airlock and docking compartment, inspected and photographed the exterior of the Russian portion of the station.
305. STS-119
EVA 1
USA: Steven R. Swanson
USA: Richard R. Arnold
March 19, 2009
17:16
March 19, 2009
23:23
- 6 hours, 7 minutes
Swanson and Arnold installed the Starboard 6 (S6) truss to the S5 truss, connected S5/S6 umbilicals, released launch restraints, removed keel pins, stored and removed thermal covers, and deployed the S6 photovoltaic radiator.
306. STS-119
EVA 2
USA: Steven R. Swanson
USA: Joseph M. Acaba
March 21, 2009
16:51
March 21, 2009
23:21
- 6 hours, 30 minutes
Swanson and Acaba prepared a worksite for STS-127, installed an unpressurized cargo carrier attachment system on the P3 truss, installed of a Global Positioning System antenna to the Kibo (Japanese Experiment Module) laboratory, and took infrared images of panels of the radiators on the P1 and S1 trusses.
307. STS-119
EVA 3
USA: Joseph M. Acaba
USA: Richard R. Arnold
March 23, 2009
15:37
March 23, 2009
22:04
- 6 hours, 27 minutes
Acaba and Arnold relocated a crew equipment cart, lubricated the station arm's grapple snares, and attempted to deploy a cargo carrier.
308. STS-125
EVA 1
USA: John M. Grunsfeld
USA: Andrew J. Feustel
May 14, 2009
12:52
May 14, 2009
20:12
- 7 hours, 20 minutes
Replaced the Wide Field and Planetary Camera 2 (WFPC 2) with Wide Field Camera 3 (WFPC III), replaced the Science Instrument Command and Data Handling Unit, lubricated three of the shroud doors, and installed a mechanism for spacecraft to capture Hubble for de-orbit at the end of the telescope's life (Soft Capture Mechanism).
309. STS-125
EVA 2
USA: Michael J. Massimino
USA: Michael T. Good
May 15, 2009
12:49
May 15, 2009
20:45
- 7 hours, 56 minutes
Removed and replaced all three of Hubble's gyroscope rate sensing units (RSUs). Removed the first of two battery unit modules.
310. STS-125
EVA 3
USA: John M. Grunsfeld
USA: Andrew J. Feustel
May 16, 2009
13:35
May 16, 2009
20:11
- 6 hours, 36 minutes
Removed COSTAR (Corrective Optics Space Telescope Axial Replacement) corrective optics package and installed Cosmic Origins Spectrograph. Repaired Advanced Camera for Surveys including get-ahead by completing steps from EVA-5.
311. STS-125
EVA 4
USA: Michael J. Massimino
USA: Michael T. Good
May 17, 2009
13:45
May 17, 2009
21:47
- 8 hours, 2 minutes
Repaired Space Telescope Imaging Spectrograph. The Space Telescope Imaging Spectrograph is a spectrograph, also with a camera mode, installed on the Hubble Space Telescope. It operating from 1997-2004 and from 2009 onward...
312. STS-125
EVA 5
USA: John M. Grunsfeld
USA: Andrew J. Feustel
May 18, 2009
13:20
May 18, 2009
20:22
- 7 hours, 2 minutes
The twenty third and final spacewalk to service Hubble and last planned EVA from the Shuttle airlock replaced the final battery module, installed Fine Guidance Sensor No. 3, removed degraded insulation panels from bays 8, 5 and 7, and installed three New Outer Blanket Layer (NOBL)s in their place, and removed and reinstalled a protective cover around Hubble's low-gain antenna.
313. ISS Exp. 20
EVA 1
Russia: Gennady Padalka
USA: Michael R. Barratt
June 5, 2009
7:52
June 5, 2009
12:46
- 4 hours, 54 minutes
Prepared the Zvezda service module transfer compartment for the arrival of the Mini-Research Module 2 Poisk, installed docking antenna for the module, photographed antenna for evaluation on the ground, and photographed the Strela-2 crane.
314. ISS Ex. 20
EVA 2
Russia: Gennady Padalka
USA: Michael R. Barratt
June 10, 2009
6:55
June 10, 2009
7:07
- 12 minutes
Internal spacewalk in the depressurized Zvezda transfer compartment, replaced one of the Zvezda hatches with a docking cone, in preparation for the docking of the Mini-Research Module 2, or MRM2, later this year. The MRM2 will dock automatically to the zenith port of Zvezda, and serve as an additional docking port for Russian vehicles.
315. STS-127
EVA 1
USA: David Wolf
USA: Timothy L. Kopra
July 18, 2009
16:19
July 18, 2009
21:51
- 5 hours, 32 minutes
JEF (Japanese Experiment Module) installed and P3 Nadir UCCAS deployed. S3 Zenith Outboard PAS deploy postponed due to time constraints.
316. STS-127
EVA 2
USA: David Wolf
USA: Thomas Marshburn
July 20, 2009
15:27
July 20, 2009
22:20
- 6 hours, 53 minutes
Transferred Orbital Replacement Units (ORUS) from the Shuttle Integrated Cargo Carrier (ICC) to the External Stowage Platform-3 (ESP3). Transferred materials included a spare high-gain antenna, cooling-system pump module and spare parts for the Mobile Servicing System. JEF Visual Equipment (JEF-VE) installation on the forward section was postponed due to time constraints.
317. STS-127
EVA 3
USA: David Wolf
USA: Christopher Cassidy
July 22, 2009
14:32
July 22, 2009
20:31
- 5 hours, 59 minutes
JPM preparation work, ICS-EF MLI, and P6 battery replacement (2 of 6 units). EVA was cut short due to high levels of in Cassidy's suit.
318. STS-127
EVA 4
USA: Thomas Marshburn
USA: Christopher Cassidy
July 24, 2009
13:54
July 24, 2009
21:06
- 7 hours, 12 minutes
P6 battery replacement (final 4 of 6).
319. STS-127
EVA 5
USA: Thomas Marshburn
USA: Christopher Cassidy
July 27, 2009
11:33
July 27, 2009
16:27
- 4 hours, 54 minutes
SPDM thermal cover adjustment, Z1 patch panel reconfiguration, JEM visual equipment (JEM-VE) installation (forward and aft), and JEM-LTA reconfigurations. S3 Nadir PAS (outboard) deployment postponed to later mission.
320. STS-128
EVA 1
USA: John D. Olivas
USA: Nicole P. Stott
September 1, 2009
21:49
September 2, 2009
04:24
- 6 hours, 35 minutes
Prepared for the replacement of an empty ammonia tank on the station’s port truss by releasing its bolts. Retrieved the Materials International Space Station Experiment and European Technology Exposure Facility mounted outside the Columbus laboratory, and stowed them in Discovery’s cargo bay for their return to Earth.
321. STS-128
EVA 2
Sweden: Christer Fuglesang
USA: John D. Olivas
September 3, 2009
22:13
September 4, 2009
04:51
- 6 hours, 39 minutes
Removed the new ammonia tank from the shuttle's payload bay and replaced it with the used tank from the station. The new tank, weighing about 1800 pounds (816.5 kg), was the most mass ever moved by spacewalking astronauts.
322. STS-128
EVA 3
Swede: Christer Fuglesang
USA: John D. Olivas
September 5, 2009
20:39
September 6, 2009
03:40
- 7 hours, 1 minute
Preparations for the arrival of the Tranquility node by attaching cables between the starboard tRussias and the Unity node, the area where Tranquility will be installed. Tranquility is targeted to arrive on STS-130 in February 2010. The spacewalkers also replaced a communications sensor device, installed two new GPS antennas, and replaced a circuit breaker.
323. STS-129
EVA 1
USA: Michael Foreman
USA: Robert Satcher
November 19, 2009
14:24
November 19, 2009
21:01
- 6 hours, 37 minutes
Installed a spare antenna on the station’s truss and a bracket for ammonia lines on the Unity module. Lubricated the grapple mechanism on the Payload Orbital Replacement Unit Attachment Device on the Mobile Base System and lubricated the snares of the hand of the station's Japanese robotic arm. Deployed the S3 outboard Payload Attach System.
324. STS-129
EVA 2
USA: Michael Foreman
USA: Randolph Bresnik
November 21, 2009
14:31
November 21, 2009
20:39
- 6 hours, 8 minutes
Installed the GATOR (Grappling Adaptor to On-Orbit Railing) bracket to the Columbus laboratory and an additional ham radio antenna. Installed on the truss an antenna for wireless helmet camera video. Relocated the Floating Potential Measurement Unit that records electrical potential around the station as it orbits the Earth. Deployed two brackets to attach cargo on the truss.
325. STS-129
EVA 3
USA: Robert Satcher
USA: Randolph Bresnik
November 23, 2009
13:24
November 23, 2009
19:06
- 5 hours, 42 minutes
Installed new High Pressure Gas Tank (HPGT) on Quest airlock. Installed MISSE-7A (Materials International Space Station Experiment) and 7B on ELC-2. Strapped two micrometeoroid and orbital debris (MMOD) shields to External Stowage Platform #2. Relocated foot restraint, released a bolt on Ammonia Tank Assembly, installed insulated covers on cameras on mobile servicing system and Canadarm 2's end effector. Worked heater cables on docking adapter.

2010 spacewalks:


#
Spacecraft
Spacewalkers
Start (UTC)
End (UTC)
Spacesuit
Duration
326. ISS Exp. 22
EVA 1
Russia: Oleg Kotov
Russia: Maksim Surayev
January 14, 2010
10:05
January 14, 2010
15:49
- 5 hours, 44 minutes
Prepared Poisk Mini-Research Module 2 for future dockings.
327. STS-130
EVA 1
USA: Robert L. Behnken
USA: Nicholas Patrick
February 12, 2010
02:17
February 12, 2010
08:49
- 6 hours, 32 minutes
Removed a protective cover on a port on the Unity node where Tranquility was berthed half way through the spacewalk. Transferred a spare parts platform for the Special Purpose Dexterous Manipulator from the shuttle to the station. Made several connections on the newly installed Tranquility node to begin its activation.
328. STS-130
EVA 2
USA: Robert L. Behnken
USA: Nicholas Patrick
February 14, 2010
02:20
February 14, 2010
08:14
- 5 hours, 54 minutes
Installed ammonia plumbing and connectors between Unity, Destiny and Tranquility and covered them with thermal insulation. Prepared the nadir port on Tranquility for the relocation of the Cupola, and installed handrails on the exterior of Tranquility.
329. STS-130
EVA 3
USA: Robert L. Behnken
USA: Nicholas Patrick
February 17, 2010
02:15
February 17, 2010
08:03
- 5 hours, 48 minutes
Installed additional ammonia plumbing between Unity and Tranquility, removed insulation and launch locks from the Cupola, installed additional handrails on the exterior of Tranquility and performed get-ahead tasks to support the installation of a PDGF on the exterior of Zarya with cable installation on Unity and the S0 truss.
330. STS-131
EVA 1
USA: Richard Mastracchio
USA: Clayton Anderson
April 9, 2010
05:31
April 9, 2010
11:58
- 6 hours, 27 minutes
Relocated a new ammonia tank from the Shuttle's payload bay to a temporary stowage location and disconnected the fluid lines to the old ammonia tank on the S1 truss. Retrieved a Japanese seed experiment from the exterior of the Kibo laboratory for return to earth and replaced a failed gyroscope on the S0 truss. Performed get-ahead tasks including the opening of a window flap on the zenith CBM of Harmony, and removed launch restraint bolts from a Flex Hose Rotary Coupler (FHRC) on the P1 truss.
331. STS-131
EVA 2
USA: Richard Mastracchio
USA: Clayton Anderson
April 11, 2010
05:30
April 11, 2010
12:56
- 7 hours, 26 minutes
The old ammonia tank was removed from the S1 truss and was replaced with the new tank. The electrical connections to the tank were made, but the fluid lines were deferred to the mission's third EVA due to time constraints since the installation was prolonged by a problem with the bolts that hold the tank to the truss. The old tank was relocated to a temporary stowage location on the station and a foot restraint was relocated in preparation for a future shuttle mission's spacewalk.
332. STS-131
EVA 3
USA: Richard Mastracchio
USA: Clayton Anderson
April 13, 2010
06:14
April 13, 2010
12:36
- 6 hours, 24 minutes
The fluid lines were connected to the new ammonia tank and the old tank was moved to the shuttle's payload bay for return to Earth. Micro-meteoroid debris shields from the Quest airlock which were no longer necessary were brought inside the airlock for return to Earth inside the Leonardo MPLM (Multi-Purpose Logistics Module). The Z1 truss was prepared for the installation of a spare antenna on the next shuttle mission, and a foot restraint was relocated in preparation for a future spacewalk. The retrieval of an external carrier plate on Columbus was deferred to another shuttle mission due to time constraints after problems were encountered with attaching the old ammonia tank to a carrier in the payload bay, and several other tasks were deferred to later EVAs due to the replanning from the problems with the mission's second EVA.
333. STS-132
EVA 1
USA: Garrett Reisman
USA: Stephen G. Bowen
May 17, 2010
11:54
May 17, 2010
19:19
- 7 hours, 25 minutes
Installed a spare space-to-ground Ku-band antenna on the Z1 truss; installed new tool platform on Dextre, and broke torque on bolts holding replacement batteries to the ICC-VLD cargo carrier.
334. STS-132
EVA 2
USA: Stephen G. Bowen
USA: Michael T. Good
May 19, 2010
10:38
May 19, 2010
17:47
- 7 hours, 9 minutes
Repaired Atlantis Orbiter Boom Sensor System (OBSS); P6 battery replacement (4 of 6 units); and removed gimbal locks from the Ku-band antenna installed on the first EVA of the mission.
335. STS-132
EVA 3
USA: Michael T. Good
USA: Garrett Reisman
May 21, 2010
10:27
May 21, 2010
17:13
- 6 hours, 46 minutes
P6 battery replacement (final 2 of 6 units); installed ammonia "jumpers" at the P4/P5 interface; retrieved a spare PDGF from Atlantis payload bay and stowed it inside the Quest airlock. The spacewalkers also replenished supplies of EVA tools in toolboxes on the exterior of the station.
336. ISS Exp. 24
EVA 1
Russia: Fyodor Yurchikhin
Russia: Mikhail Korniyenko
July 27, 2010
04:11
July 27, 2010
10:53
- 6 hours, 42 minutes
Prepared Rassvet module to allow future Russiasian vehicles to dock using Kurs (docking system) automated rendezvous system capability. Routed and mated command and data handling cables on Zvezda and Zarya modules.
337. ISS Exp. 24
EVA 2
USA: Douglas H. Wheelock
USA: Tracy Caldwell Dyson
August 7, 2010
11:19
August 7, 2010
19:22
- 8 hours, 3 minutes
Attempted to replace failed ammonia pump module. The spacewalkers did not complete all of the planned tasks due to a quick disconnect that got stuck and would not release. The pair had to complete a "bake-out" in order to ensure there was no ammonia on their suits before re-entering the Space Station.
338. ISS Exp. 24
EVA 3
USA: Douglas H. Wheelock
USA: Tracy Caldwell Dyson
August 11, 2010
12:27
August 11, 2010
19:53
- 7 hours, 26 minutes
Completed removal of failed pump module from the S1 truss and began installation preparations on the replacement pump.
339. ISS Exp. 24
EVA 4
USA: Douglas H. Wheelock
USA: Tracy Caldwell Dyson
August 16, 2010
10:20
August 16, 2010
17:40
- 7 hours, 20 minutes
Installed new pump module on the S1 truss.


Ref.: #248 - update: 29.06.11 Home